How To Paint Chassis Of Rc Car? Don’t Get Into A Race With Paint Drying!

Spread the love

If you’re an RC car enthusiast, chances are you have already spent quite a bit of time customizing your vehicle to make it stand out. But have you considered painting the chassis? The process may seem daunting at first, but with some patience and attention to detail, you can create a stunning paint job that will impress everyone on the track.

The first step in any painting project is preparation. You’ll need to clean the chassis thoroughly with soap and water or alcohol wipes to remove any dirt or grease. Next, use sandpaper (200-400 grit) to rough up the surface so that the paint adheres better. Make sure not to sand too hard and damage any important parts!

Once everything is clean and dry, it’s time for primer. This crucial step ensures that the topcoat has something to stick to and also helps prevent rusting over time. Apply several thin layers rather than one thick one, waiting 10-15 minutes between coats.

Tip: If there are areas of your chassis where duct tape was used as masking when modifications were made earlier down-shifts consider using rubbing alcohol during cleaning those sticky spots instead of soap-water solution

Finally, we arrive at the fun part – applying color! Spray cans of automotive enamel work great if done properly else get yourself a brush-on acrylic kit suitable for plastics like Tamiya Color Acrylic Paint series which provide best results even on smaller RC models too while giving more control over how much coat goes onto each area avoiding blotches from spray application especially near components box/mountings

This guide should give anyone looking into How To Paint Chassis Of Rc Car enough confidence towards undertaking this DIY activity without fear of mess ups provided they follow instructions carefully . So get ready race enthusiasts bend their competition by putting in brighter colors altering look thus aiding visual telemetry during the race!

Choose The Right Paint

The first thing you need to do when painting the chassis of your RC car is to choose the right paint. Not all types of paint are ideal for this purpose, and selecting the wrong one could ruin both your project’s appearance and performance.

Avoid water-based paints: Water-based paints may seem like an excellent choice because they are easy to clean up with soap and water once dry. However, these kinds of colors may not adhere well enough for long-term use on a vehicle that moves around so much – especially after coming into contact with gravel, dirt, or other harsh surfaces.

“Water-based paints can flake off faster than oil-based options.”

Dedicated automotive spray paint: If you want durable protection that will last over time, then consider investing in dedicated auto or plastic-specific sprays specifically formulated to bond strongly with different materials used for constructing Rc Cars such as glass-fiber-reinforced plastics (GFRP), carbon fiber reinforced plastic composites (CFRP) or even metals depending upon which metal has been primarily used in making it. These come in various finishes and textures ranging from matte black finish to glossy ones.

“Make sure you apply light coats. Don’t try going heavy straight away!”

Sand before applying: Make sure that any surface scratches havebeen sanded beforehand using 220 grit sandpaper so paint adheres better without risking flakes peeling off quickly.As always consult the label of specific type ofpaintyou buy since each brand might explain howto properly preparematerial & area differently. In Conclusion: Choosing best qualityspray canscanresult ina stunning lookingvehiclethat lasts longerthan normal paintedcars but if some people enjoythe satisfactionofhand painting larger areas withbrushes sinceit canbecome more precise and targeted for intricate details.Bestways to paint willalways dependuponpersonaldesire. so, it is importantto keep experimentingandfinding what works bestfor you.

Consider the type of material the chassis is made of

The first thing you need to consider when painting your RC car’s chassis is the type of material it’s made of. Most commonly, RC car chassis are made from either plastic or metal.

If your RC car has a plastic chassis, you can use a spray paint specifically designed for plastic surfaces. Make sure to clean and dry the surface completely before painting. You may also want to prime the surface with a plastic primer beforehand to ensure proper adhesion and smoother finish.

If your RC car has a metal chassis, then it’s recommended that you use an enamel-based paint designed for metals. Enamel paints tend to adhere better on metallic surfaces as they contain resins that melt together with substrate during curing process forming strong bond.

Here’s what one expert recommends:
“Always choose high-quality paints regardless if it’s for plastics or metals because these types of materials expose our cars in all sorts of harsh environmental conditions such as sunlight, rain and even scratches.”
To get maximum durability and protection against damage over time, some painters suggest applying clear coat layer once base coat is fully cured while others prefer not putting any finishes at all since there may be slight color variation upon application which they want displayed more vividly.

In conclusion, choosing the right type of paint depending on the material being painted ensures long lasting durability and glossy appearance on your RC Car Chassis!

Prepare The Chassis

The first step in painting the chassis of your RC car is to prepare it properly. This means you need to remove all previous paint and clean any dirt, grease or debris present on it.

You can use sandpaper or a wire brush to scrape off old paint from the metal surface. Be careful not to damage thinner parts by using coarse-grit sandpaper. After removing the old paint, wash off any remaining bits with warm soapy water and let dry completely before starting again.

Note: It’s important that you wear protective gloves during this process as scrapes and layers of dust are inevitable when working with an older model; therefore wearing protection equipment at such times is necessary for safety precautions during the process.

“Cleaning properly beforehand will ensure that no residue remains on the surface which could react negatively with primer coats and further application.”

If there are spots where corrosion has compromised structural integrity on specific areas of your vehicle like brackets etc., they should be either repaired or replaced because rusty items can reduce its working lifespan and possibly cause accidents while maneuvering mid-risk action scenes within close proximity movement ranges if neglected or ignored. TIP: Use plastic bags or tape pieces covered over openings/nearby holes illiterate spillage resistance on surrounding surfaces especially tyres, wheels, axles upon spraying into fine finishes depending on color preference choices!

Cover Up Parts You Don’t Want To Paint On

In order to maintain professional-looking work reflective of mechanical perfectionists’ obsession-level processes even beyond automotive indusries whilst minimizing costs associated through excessive spending capital invested upon repair jobs due lack adequate care handling techniques well-articulated by professionals often guided adequate experienced backgrounds achieving expected results through ensuring cover-up appropriate areas with masking tape or plastic sheets to avoid getting paint onto surfaces you don’t want painted. The habit of being precise as possible is key here!

“Spending time and effort on masking up your vehicle before painting is one of the most important steps to take in order capture that professional custom look without compromises – resist temptations by cutting corners just- simply forget it!”

Remove all the components from the chassis

If you’re looking to give your RC car a fresh new look, there’s no better way than painting the chassis. Before starting with any paint job, it is important that you know how to take apart your vehicle and remove all of its parts.

The first step in this process is to clear up some space and collect all necessary tools which include Screwdrivers (Flathead, Phillips), pliers or side-cutters may be needed if there aren’t any release clips along with cleaning materials such as rubbing alcohol, degreaser or silicone remover depending on what type of contaminants are present.

You must now identify each component connected to the chassis by referring to an instruction manual for assistance. Once identified start removing them carefully without damaging any surrounding areas then place small screws/other fittings in labeled bags/envelopes – separation according to where they belong will simplify reassembly later down-line when everything has been painted.

Note: You should ensure that cables placed near moving joints don’t get cut/crushed in-case things popoff abruptly – avoid compulsive force incorporation while taking out these pieces!

To protect sensitive electronics such as batteries, ESC’s etc., wrap these items tightly with plastic wraps so paint fumes/water won’t spoil their internal capacitors whilst painting or washing off excess spray-paints!

Once every detachable part is removed clean & sandpaper surfaces properly thus ensuring uniform coat adhesiveness- however always remember; too much sanding can deteriorate finish quality putting a user at risk for malfunction during use early on after completing procedure thereby cutting back quite time put into revamp unnecessarily!! Therefore proceed cautiously…

In conclusion, “Strip your RC model car completely before respraying. Failure to do so affects the quality of your finish; bits and pieces glued or double-sided taped on may not stick during/packing hence taking apart individual sectors remarkably makes every other step smoother.”

Sand The Surface

One important step in painting the chassis of an RC car is to sand the surface. This allows for better paint adhesion and a smoother overall finish.

Befor you start, gather some fine-grit sandpaper around 400-600 grit. Sand any rough or uneven areas on your chassis thoroughly until they’re smooth to the touch.

“Sanding is essential for preparing the surface of your RC car’s chassis before painting it.”

If there are already existing layers of paint on your chassis that aren’t flaking off, you don’t necessarily need to remove them if they’re still adhering well; just give them a light sanding all over with finer paper. However, flaking or chipped paint must be removed so as not to interfere with new layer application.

NB:Remember always rinse away dust from previous steps carefully prior proceeding forward .

Make sure the surface is smooth and free of scratches

If you want to give a new look to your RC car, then painting its chassis can be an excellent way to achieve that. But before starting with the process, ensure that the surface of your RC car’s chassis is smooth enough for paint adhesion.

Achieving a smooth finish requires proper preparation work, and scratching or roughing up any surfaces that will be painted won’t help make it smoother. In fact, impacts like these harm the overall structural integrity of your vehicle. To avoid this mistake altogether – take time in inspecting all corners as well – begin by cleaning off any dirt or debris using soap water and dry thoroughly.

The next step involves sanding down irregularities on metal more precise than plastic parts since they might have seams where sheets were welded together creating additional pores. Using high-grit sandpaper such as 400-600 grit makes light work when rubbing available rust away from plated surfaces without leaving significant abrasions behind (which would ironically cause unevenness) underneath layer coats applied later on top during primers application truces every minute shred leftover dust quickly past use just after lock one volatile wipe-down cloth up onto area gone through.

“Sanding takes time but don’t rush it! Spend extra attention around edges – sloped rather than constant – these are easiest points prone adherence issues.”

Protective masking tapes also play an important part in keeping neat lines between colors; painters should cut each tape section long enough so paintwork does not bleed-too baggy or too tight could ruin outcomes depending upon design elements involved at their best creatively speaking!.

In conclusion, sanding out imperfections until achieved a flawlessly leveled surface transforms better into success rates regarding spray paints utilization desired plain objectives designs chosen. Becoming patient during progressive steps here matters more than any since haste wrecking overall outcomes envisaged.

Use a sandpaper with a fine grit

When it comes to painting the chassis of your RC car, using the right type of sandpaper is essential. A fine-grit sandpaper ensures that you achieve a smooth and even surface before applying paint.

Sandpapers come in various types ranging from coarse to extra-fine. The number on the back of each sheet represents its grit or coarseness level—the higher the number, the finer the grit. A 220-320 grit paper is perfect for preparing metal surfaces as it removes surface imperfections while leaving behind uniform scratches that create an excellent bonding surface for primers and paints.

Before getting started, make sure to clean off any dust particles or grease on your chassis with mineral spirits so that your primer can adhere correctly. Next, wrap a piece of 220-320 grit sandpaper around a small block and gently begin scrubbing at rough areas until they’re nice and smooth.

“Remember always to sweep away debris after every few passes.”

If you notice any rust spots during this process, use steel wool or an abrasive pad to remove them carefully – these spots will also need some attention because they could lead to corrosion down-the-line if left untreated.

To ensure complete coverage when painting with multiple colors or coats requires intermediately-sanded layers – making certain no ridges formed by overspray show up anywhere else either than where intended; we recommend lightly scuffing each layer with very-high fitted abrasives like micro finishing papers (‘worn-out’ style)

Conclusion: I think using a high-quality sandpaper makes all the difference between having great results versus disappointing ones. Chassis are one part that often gets overlooked when adding color schemes but taking extra care here goes long ways ensuring the beautiful end product you always wanted.

Clean The Chassis

Before you can paint the chassis of your RC car, it is important to ensure that it is clean and free from dirt and debris. This will allow the paint to adhere properly and prevent any imperfections in the finished product.

To start, remove all electronic components or cover them with tape or plastic wrap to protect them from water or cleaner. Use a brush, such as an old toothbrush, to remove all dirt, dust, and debris from the nooks and crannies of the chassis.

“Cleaning the chassis may seem like a tedious task but it’s crucial for achieving a smooth finish.”

You can also use compressed air to blow away any stubborn particles. Once you have removed all surface level grime, soak a microfiber cloth in soapy water. Gently wipe down every inch of the chassis making sure not to neglect any areas where dirt could be hiding.

If there are more stubborn spots on your chassis that refuse to come off even after soaking in soapy water then try using rubbing alcohol or vinegar. But remember when applying these chemicals make sure they don’t get exposed on sensitive part of electronics because both substances can damage electrical components if absorbed into them excessively.

“The key is patience! Take your time cleaning every crevice and corner until everything looks spotless!”

Dry off the entire chassis thoroughly with another dry microfiber cloth before proceeding process further toward painting step by ensuring complete drying first else this might ruin outcome result due uneven distribution caused by moisture captured during wet stage”

Use a degreaser to remove dirt and oil

If you want to paint the chassis of your RC car, it is essential that you clean the surface beforehand. Dirt and oil can prevent the paint from adhering properly, which can result in a bad finish or chipping paint. One way to remove stubborn grime is by using a degreaser.

A degreaser works by breaking down grease and oils so that they become soluble and easy to wash away with water. This makes it an ideal solution for cleaning metal surfaces contaminated with dust, carbon deposits, road film, and other residues that may have accumulated over time. To use a degreaser:

“Make sure that the area where you will be applying the cleaner has good ventilation.”

The first step is to read the manufacturer’s instructions as different products may require specific handling procedures. Next, prepare your work area by covering any sensitive parts like electronics or bearings, then apply the degreaser directly onto the dirty areas on your chassis.

You should allow enough time for the product to work its magic before washing it off entirely; most formulas become fully effective after five minutes of application. It’s best not to let any residual cleaner dry on your chassis’ surface because this could leave behind unwanted streaks when painting later on.

Safety precautions
  • Always wear gloves when working with chemicals like degreasers as they can irritate skin
  • Wash hands thoroughly once done using water and soap
  • Avoid getting any liquids into your eyes or inhaling fumes produced during usage of these harsh chemicals
  • Dispose of used cleaner according to local regulations
“Remember never use acidic cleaners on aluminum, as they can eat into and corrode the metal”

Once finished cleaning with a degreaser remove all traces of chemical cleaner before painting using running water or wipe off with clean cloth. Failure to do so may mess up your paint job.”

If you follow these tips when applying a degreaser to your RC car chassis, you should be able to see great results after you’ve repainted it.

Mask The Chassis

If you want to paint the chassis of your RC car, there are certain steps and preparations that should be taken beforehand in order to achieve satisfactory results. One important step is masking.

What is masking?

“Masking means covering or protecting parts of the object that you don’t want painted with a material that will prevent paint from touching those areas” – Randy Slone

The purpose of masking is to protect any parts on the car that shouldn’t be painted. In other words, it helps prevent overspray onto places like tires, axles, engine components and shocks. Some experts recommend using high-quality automotive detailing tape for this process as it won’t leave residue nor damage the body when removed.

How do I mask my RC car?

“The secret to doing well lies not so much in what products you use but rather how carefully they’re applied.” – Jared Gall

Careful preparation is critical when undertaking this task to avoid ruining hours of hard work.“It’s worth taking whatever time necessary before painting begins, ” suggests Jared Gall at Popular Mechanics Magazine. Here are some useful tips:

  • Clean up your workspace: To start off clean all dust accumulated around where you’ll be working;
  • Select an area away from wind drafts: This minimizes air currents which could deposit particles and hair into wet-paint
  • ;
  • Tape guide lines where necessary on your vehicle such as door jams & wheel wells.
  • MASK! Start by taping out windows or lights since these have curved corners that can cause jumping if masked too roughly;;
  • Cut the tape appropriately: Choose a thickness dependent on size of area to cover and insert onto vehicle;
  • Press down firmly aligned with areas boundaries – Keep constant pressure with fingers as you apply for best stick.


In summary, masking is only one part of painting your RC car. By keeping your workspace clean, avoiding wind drafts and using high-quality automotive detailing tape you can successfully protect any parts of the body that should not be painted. The results will speak for themselves!

Use tape to cover areas that you don’t want to paint

If you are looking for a way to protect certain parts of your RC car while painting, using tape is the best solution. By covering the specific area with tape, you can prevent paint from getting onto it and ruining its appearance.

The first step in preparing your chassis for painting involves cleaning it well with soap and water. Make sure there is no dirt or grease on it so that the paint will adhere correctly.

When ready to start applying paint, carefully apply masking tape around areas that you do not wish to be painted. It’s important to ensure that all edges are sealed tightly- if any part of the surface isn’t taped down properly, this could lead to gaps where unwanted spray might leak through and blotch up an already perfect body design!

“The key thing here is patience when taping off those hard-to-reach spots.” -RC Car Enthusiast

This makes sense since more intricate designs involve much smaller details like tight fit corners which means they need extra delicate handling during tapes placement procedure.You’ll also want good quality painter’s tape; something designed specifically for this purpose as regular scotch-tape won’t cut it.”


  • Be mindful about how many coats of paint go over thin layers: too many thick coatings make sprays run faster across curves leading problems such as peeling soon after finishing.
  • If possible remove wheels before beginning work so easier access points can help minimize chances accidental contact areas subsequently avoid smudging later stages processing cycles.
  • “Don’t forget sandpaper! A little smoothing out rough surfaces adds brilliance giving necessary texture prior starting on final touches”.

Paint The Chassis

If you’re looking to add some personal flair or simply just protect your RC car’s chassis, painting it might be the way to go. However, before starting to paint the chassis of an RC Car there are certain precautions and steps that should be taken.

Clean Your Chassis:

The first step is cleaning your chassis thoroughly with soap water or rubbing alcohol to remove any dirt residue. Afterward, make sure the surface is completely dry so that no moisture remains on the material.

Sanding Process:

Before painting a plastic chassis for an RC car vehicle, sandpaper will give better adhesion by providing abrasive texture which provides good bonding strength between layers of primer and paint onto its surfaces. In contrast, aluminum or steel can get damaged if sanded too hard due to their metallic nature- hence scuffing them gently would suffice for creating solid groundwork required in making each layer bond well with one another through time before being painted over again later down below sequence as needed until satisfied enough after drying period given at end results where coating thickness varies proportionately towards requirements set beforehand from prep work done earlier throughout process itself applied carefully without skipping any steps necessary along way!

Making Masking Area:

To create crisp lines when painting select areas considering those parts yourself want accentuated which use masking tape border around aforementioned areas so they don’t overspend accidentally and produce clean finish look wanted once everything comes together nicely!

“Patience and care are critical during this task.”

This quote holds weight since rushing things could easily ruin all previously accomplished efforts including mistakes made latter concerning slight imperfections like drips present upon final product inspection leading back again rework entire job requiring correcting color mismatches occurred within process duration indicative errors caused individual moment slip-ups allowing time rework to be wasted when that could have spent previously taking care of other things downline equal importance yet not prone making ones about happen during activity surface like scratches, dings etc.

All in all, the process on how to paint a chassis for an RC car requires attention and focus. Each step should be taken thoroughly needed into account before carrying out application that follows throughout entire sequence till it’s completed finish satisfactory levels desired initially set beforehand final touches added lastly if necessary- certainly worth effort put towards ensuring well-painted piece equipment capable standing test times remaining intact despite use whether purpose work done shows while driving track or kept aesthetically pleasing eye amongst peers groups which collect hobby fighting likeliness better achieve goals set minds collectively as unit having similar interests appreciate art motor vehicle design functionality combined!

Apply a primer coat before the final paint coat

If you want to give your RC car chassis an excellent finish, applying a primer coat is essential before painting it. The layer of primer will provide better adhesion for the topcoat and make it more durable from scratches or chips.

A good quality primer should be lightweight but cover efficiently on metal surfaces that resist corrosion caused by moisture, chemicals, or UV rays. Primers come in different types such as acrylic, epoxy resin, rust-inhibiting, and sandable primers designed for various applications.

You can apply a primer using either spray cans or airbrushes depending on the size of your RC vehicle’s bodywork. Applying with a spray can may be easier than airbrushing since its method only requires pointing and spraying over large areas easily while ensuring even coverage. However, if you are looking for detailed work where precision is needed like masking off sections around intricate designs use an airbrush system instead.

“The benefits of using a high-quality automotive plastic adhesive promoter/primer combo product cannot be overstated.” – Steven Mizek

When choosing which primer to apply that goes best for your specific needs look at online reviews but also check out what fellow hobbyist recommends through discussion forums or Facebook pages etc…. never mix brands when doing this kind job because they tend not compatibility together resulting bad consequences after drying picking up dirt and other factors that mean redoing again plus time wasted unnecessarily.

An added benefit of having properly applied multiple coats is easy washing during cleanup after each practice session demonstrating pride ownership standing beautifully dauntingly biting track’s dust seething yet confidently always ready battle whatever course awaits ahead!

Allow each coat to dry completely before applying the next coat

If you want to get a good finish on your RC car’s chassis, then it is essential that you follow some critical steps. Painting the chassis of an RC car is not as simple as painting a wall because it needs to withstand extreme conditions during racing like dust, water, and collisions.

The first step in this process is to clean the surface properly. The parts that need painting must be free from all debris; sandpaper can remove any loose paint, dirt or corrosion which will also help with adhesion of new coats going forward.

The second step would be masking off any areas where you don’t want paint applied:
“Masking tape ensures no overspray onto undesirable sections so we have more defined edges for our work” – said Simon King from Tinkerer’s toy shop.

This leads us back to perhaps one of the most important stages in this project: allowing each coat of paint time enough space between applications so they’re fully-dried before adding another layer overtop them — doing otherwise results in uneven coverage patterns at best!

In conclusion, taking these precautions when painting your RC Car Chassis guarantees lasting results that go beyond initial satisfaction; following tips such as proper cleaning cycles prior-to-painting sessions ensure maximum adherence while running through various speeds on tracks around town.

Frequently Asked Questions

What materials do I need to paint the chassis of my RC car?

To achieve a professional-looking finish when painting the chassis of an RC car, you’ll need some essential tools and materials. These include sandpaper with varying grits for smoothing out rough spots on the surface to be painted and improving adhesion between layers

Do I need to remove all the components from my RC car before painting the chassis?

It is highly recommended that you take apart your remote control vehicle completely, down to every single nut and bolt. This will ensure that only the outer shell/ body remains while other internal parts are removed away. By doing this step-by-step process, further damage can also be avoided, necessary maintenance work gets done with ease, it provides better access-points & easy application of paints without any hindrance making sure each corner has been coated properly

How do I prepare the chassis surface for painting?

The key to achieving good results depends largely upon proper surface preparation which entails removing all debris or contaminants (oils, dirt) since they could compromise our intented result by chipping later due lack adhesive strength & not being able hold up after last coat too. Use fine-grit sandpaper as per requirement over bare areas till everything looks smooth – getting rid scratches if required- then wipe gently using damp soft cloth / lint-free tack rag leaving no dust behind thus facilitating us towards cleanliness icing without adding stress levels high upto minute details including bolts/nuts etc broken/freezed-out

What type of paint should I use to paint the chassis of my RC car?

You can buy ready-made spray paints from hobby stores, but automotive-grade acrylic enamel offers better durability and adhesion in addition to a wide range of available colors giving more control & finishing options than expected. This is due to its high pigment count that ensures coverage without compromising on texture or leaving patches / discolouration plus fast drying, thus chipping easily fixed if occurred by chance too.

What is the best technique to use when painting the chassis of an RC car?

The most important aspect while applying any coat- uniformity! Always shake sprays well & hold six-to-seven inches distance away then apply thin even coats with smooth sweeping motion till surface looks solid/dry.Each layer needs be given attention thoroughly after it dries (15 mins minimum) removing particles born using sandpaper before next coat application ensuring no missed spots especially at corners/edges risking unwanted drips/marks later-on

How long should I wait before reassembling my RC car after painting the chassis?

To achieve perfect results means letting your painted surfaces dry up completely -min 24 hrs would suffice not just looking dried off but healing within which keeps our investment risk-free. So waiting for time frame required solves many potential issues as this will only ensure that masking tape residue does not stick onto screws/bolts hence maintain integrity throughout safe usage conducting final checks seeing nothing was left behind starts bringing joy/calmness thinking about upcoming delightful moments during driving experience

Do NOT follow this link or you will be banned from the site!